Видео

No me permite cargar libreria

Can we make this rotations continuous in one direction...say in one direction for two minutes

Can i use this driver for 4.2v rated stepper motor?

Köszönjük!

Is the reading you are showing in RPM?

Yo i have the brushless motor controler 48v and 250w, motor 48v 250w so max speed on e bike is 36kmh what to do on the controller to go faster

Hi, can do with rotary potentiometer control position? Thank you very much.❤

verry nice ! but i can't find ESP2Relay Controller apk ..help please!

errors out - "fatal: destination path 'lcd' already exists and is not an empty directory."This video is no longer valid - the instructions here no longer work.

Thank you po!

Just to let you know that I don't watch videos with boom boom music !!

Ye ky backchodi hai

how can ı make pc817 card do you have cırcuıt dıagram

But you not share code !

where have you bough those 12" wheels? What they are made for?

Would that liberia work for ARGB?

jeezz that worked

Are you putting a pi in the Doppler? Dammit

Can we use this for measuring mobilephone battery capacity

What do you mean by turn the line

very funny . But you not connected ground jumper

It's always a puzzle. Just one swap away. It can infect a whole set of project parts.

To determine the load capacity of a DC motor, we need to consider several factors, including: 1. Motor power (250W) 2. Current (24A) 3. Speed (310 RPM) 4. Gear ratio (not specified, assuming 1:1 for simplicity) A general rule of thumb for DC motors is to use the following formula: Load capacity (in kg) ≈ (Motor power × 1000) / (Speed × Gear ratio) Plugging in the values, we get: Load capacity ≈ (250W × 1000) / (310 RPM × 1) Load capacity ≈ 806.45 kg However, this is a rough estimate and doesn't take into account factors like: - Friction - Inertia - Motor efficiency - Gearbox efficiency (if applicable) To be more accurate, let's consider a safety factor of 0.5 to 0.7 (depending on the application). This reduces the estimated load capacity to: Load capacity ≈ 403.22 kg to 564.51 kg So, the DC motor can likely handle a load of around 400-560 kg (880-1234 lbs), depending on the specific application and conditions. Keep in mind that this is still an estimate, and actual performance may vary. Please provide more details about your project, such as the gearbox ratio, wheel diameter, and application, for a more precise calculation.

How to make it line following?

Can we make it like following?

Can we make it line following?? Please reply 🙏

I used the analog output for this encoder. I had trouble getting the readings first but then I found out that the GPO pin had to be connected to 3v3 or 5V (depending on the supplied voltage). So I did that and got some readings but then the readings were inconsistent. I then realised that the magnet has to be at a perfect distance from the chip. Half a mm change means either you are getting some values or nothing at all. I wonder if that would change if I tried I2C. Happy to hear any suggestions...

I use this method: Insert a 1microFarad capacitor between EN and GND.

Use karke bhi dikha dete🙂

you're the greatest

Good job .if I went put stepper motor withe encoder how I do that

Thank you for this tutorial.

This is spectacular sketch for Arduino Thanks

Thank You Very Much ! for ilustration "

helpful tech video ,great music , what else does one need hhhhh, thnx

An hour searching for information about this before burning my board xd. Thanks :3

Amazing

How many pulses its goves in on revolution PPR rate please

How much weight can it Lift?

From where i can buy that Wheel

Thanks for letting me know how to connect these. Wire

Please provide code

this lcd screen is attatched to smth i dont see on my lcd screen. what is this blue thing with less pins than the lcd itself? can anybody help me out? im new xD

n' est plus d actualité il faut travailler avec ( remotexy )beaucoup moins chers avec IA moi novice: cest du gâteau

Amazing!!

We are working on this issue with my teammates at school. Is there any chance of getting this code? If so my friends and I would be very happy.

Solution for Arduino IDE users: turn the version of the esp32 board library from to 3.0.2 and it will solve the issue of constantly rebooting in the terminal. 21 jul 2024

My display in tuchscreen is not working tell me answer

What about led connectors?